|
|
« Last Page | viewing entries 1-15 of 1908 |
Next Page »
|
Length: 5:26 -
Rating: 4.818182 (22 ratings) -
View: 12695 -
Author: hamradiocrazy
In Part 1 I have installed the support base for the Hustler 4BTV vertical antenna, and the DX Engineering radial plate. I talk about my plan for the radial f...
Tags
|
|
Length: 28:42 -
Rating: 4.912409 (137 ratings) -
View: 18499 -
Author: Dave Tadlock
A 10 meter ground plane antenna that can be mounted on a mast or used as a ground mounted vertical antenna.
Tags
|
|
Length: 3:43 -
Rating: 5.0 (14 ratings) -
View: 337 -
Author: AzPapaLes
Just a quick vid showing some friends helping me get the masts raised so I can get my G5RV antenna up. Thank you AfroPrepper and friends for the help! Thank ...
Tags
|
|
Length: 10:59 -
Rating: 5.0 (15 ratings) -
View: 345 -
Author: dafrogtoad
The day fianallt came. Time to hiost up adn antenna and see what happens. I was given this Alpha Delta as a "radio warming" gift. I don't know much about it ...
Tags
|
|
Length: 34:29 -
Rating: 0 (0 ratings) -
View: 134 -
Author: utuberevealer
1959 -- Christine in Confirmation Gown front of 117 Summer (very Short); Shorty's 1955 Buick Convertible in garage at 117 Summer St; Family's 1956 Chevy with...
Tags
|
|
Length: 23:10 -
Rating: 4.5555553 (9 ratings) -
View: 232 -
Author: xxRenaissanceManxx
Video review of the MFJ-929 Automatic Antenna Tuner. The MFJ-929 is an amateur radio automatic antenna tuner that is used to match an antenna or wire to your...
Tags
|
|
Length: 3:56 -
Rating: 5.0 (15 ratings) -
View: 9056 -
Author: hamradiocrazy
In Part 2 I have connected 6 radials to the DX Engineering radial plate under the Hustler 4BTV vertical antenna. I show how to make a solid connection, and d...
Tags
|
|
Length: 5:9 -
Rating: 5.0 (10 ratings) -
View: 3580 -
Author: on4amg
Extra heavy duty 60 feet/18m, 2.5m2/32 sq ft wind load rating, aluminum self supporting motorized crank up/tilt over tower. This will carry a HF multiband ya...
Tags
|
|
Length: 5:13 -
Rating: 4.8461537 (26 ratings) -
View: 2151 -
Author: dighsx
Title pretty much says it all. I show how I get the stale smoke smell out of my car. I show off my ham antenna setup at the house downstate and rant about ha...
Tags
|
|
Length: 3:51 -
Rating: 5.0 (3 ratings) -
View: 1866 -
Author: TimTools99
I have my tower up and antenna and rotor installed. Now it's time to get my station equipment grounded.
Tags
|
|
Length: 1:18 -
Rating: 5.0 (18 ratings) -
View: 10164 -
Author: machineman97
How to install a Breedlove Mount stake pocket bracket for cb or ham radio antenna mount on your pick up truck. A solid brass EZ over antenna mount is also sh...
Tags
|
|
Length: 4:25 -
Rating: 5.0 (5 ratings) -
View: 838 -
Author: Alan Senechal
Look at the DX Engineering radial plate hardware and assembly process. The plate is pre-assembled before taking it to the antenna site.
Tags
|
|
Length: 0:52 -
Rating: 4.826087 (23 ratings) -
View: 15249 -
Author: Dave Tadlock
Testing my ham radio tower and new winch before installing any antenna. I hired a welder to build the tower stand for me. I poured the concrete and installed...
Tags
|
|
Length: 1:7 -
Rating: 5.0 (15 ratings) -
View: 1904 -
Author: PortableQRP
This is a short video of my contact today into Serbia, using my SGC SG-2020 with less than 20 watts output and my indoor 46" magnetic loop antenna. The math ...
Tags
|
|
Length: 1:23 -
Rating: 0 (0 ratings) -
View: 109 -
Author: IZ7PDX
My AL811H is ok now after a careful monitoring of the electrical circuit and after replacing the blocking capacitor on the plate! TNX "HAM RADIO WEB" FORUM h...
Tags
|
« Last Page | viewing entries 1-15 of 1908 |
Next Page »
|
|
|
There was an error processing the request. Please try again.
;)
;)
;)
;)
;)
;)
;)
;)
;)
;)
;)
;)
;)
;)
;)
