|
|
« Last Page | viewing entries 1-15 of 3000 |
Next Page »
|
Length: 8:14 -
Rating: 4.6363635 (11 ratings) -
View: 2000 -
Author: EndOfTheRoadFamily
I put together this HAM radio tower out of 2 inch water pipe. The pipe is schedule 40 and 21 foot long. I have 2 lengths coupled together in three legs of th...
Tags
|
|
Length: 13:1 -
Rating: 4.6883116 (77 ratings) -
View: 23637 -
Author: drez20001
PVC Tube Ham Radio Tower Project.
Tags
|
|
Length: 10:5 -
Rating: 5.0 (3 ratings) -
View: 160 -
Author: MalenyDingoHire
I needed a stick to hang my dipoles or G5RV off. This was a cheap and simple solution to get me going with HF. It didn't cost much, It doesn't look too bad, ...
Tags
|
|
Length: 3:48 -
Rating: 3.6666667 (24 ratings) -
View: 38879 -
Author: MrFarallon
Here is the antenna mast I made out of 3/4 pine boards and an aluminum tubing. The antenna is a Comet GP-15 tri-bander (70cm, 2 meter, 6 meter). The mast is ...
Tags
|
|
Length: 3:11 -
Rating: 0 (0 ratings) -
View: 10323 -
Author: ltaprojects
Quick Start Guide to setting up a 25 foot tall inflatable antenna tower invented by LTA Projects...and built especially for Amateur Radio and for CERT Teams....
Tags
|
|
Length: 3:35 -
Rating: 5.0 (7 ratings) -
View: 1276 -
Author: Aaren Jensen
Following sources online and a few modifications on my own I just completed an inexpensive antenna mast made of wood. It's about 42 feet long with about 38' ...
Tags
|
|
Length: 3:43 -
Rating: 5.0 (14 ratings) -
View: 373 -
Author: AzPapaLes
Just a quick vid showing some friends helping me get the masts raised so I can get my G5RV antenna up. Thank you AfroPrepper and friends for the help! Thank ...
Tags
|
|
Length: 4:51 -
Rating: 4.771739 (92 ratings) -
View: 90945 -
Author: DuanesVideos
July 22,2012 update: Benny is now a Silent Key. We will miss him, his antennas, and his signal. A short time lapse video of Benny, John, and the crane puttin...
Tags
|
|
Length: 2:22 -
Rating: 4.8958335 (48 ratings) -
View: 34694 -
Author: ph0as
This is my solution for an amateur radio station in a suburban area and its restrictions. Read (and see) all about my solutions on: www.ph0as.nl Hear you on ...
Tags
|
|
Length: 4:43 -
Rating: 5.0 (11 ratings) -
View: 5336 -
Author: vu2pop
Tilt Crankup Mast for Ham Radio by VU2POP , homebrew crankup tilt & crankup mast , mounted with homebrew AZEL rotors, homebrew Vhf / Uhf yagis for sat work.
Tags
|
|
Length: 4:55 -
Rating: 5.0 (34 ratings) -
View: 14299 -
Author: Richard B
This is a basic video of the assembly and use of the mobile winch mast system using 2" sleeved tubes . This is lifting 30' of pole.
Tags
|
|
Length: 40:52 -
Rating: 0 (0 ratings) -
View: 79 -
Author: ukspeedtraps
Michael Brown - East Staffordshire Borough Council - Planning Department gives a talk about Masts and Planning Rules to Burton Amateur Radio Club - December ...
Tags
|
|
Length: 5:52 -
Rating: 4.7647057 (17 ratings) -
View: 7835 -
Author: TimTools99
The primary rule for protecting ham radio equipment against lightning damage is connection of all elements to a SINGLE, low impedance grounding point.
Tags
|
|
Length: 2:10 -
Rating: 4.733333 (15 ratings) -
View: 13175 -
Author: MrTouristica
Military surplus aluminum masting tubes. Each tube is 48 inches long by 1.785 inch outside diameter (inside diameter 1.57 inch), wall - 0.11 inch, and weigh ...
Tags
|
|
Length: 4:23 -
Rating: 4.870968 (62 ratings) -
View: 20377 -
Author: twmckim
Explanation of benefits of fiberglass poles as supports for HF wire antennas.Note: I put the fed end of the antenna up high on the pole due to past success i...
Tags
|
« Last Page | viewing entries 1-15 of 3000 |
Next Page »
|
|
|
There was an error processing the request. Please try again.
;)
;)
;)
;)
;)
;)
;)
;)
;)
;)
;)
;)
;)
;)
;)
